Quality Control of Shoes Production Using Methods Statistical Quality Control and Failure Mode Effect And Criticality Analysis at PT. Ide Bangun Mandri
Pengendalian Kualitas Produksi Sepatu Dengan Menggunakan Metode Statistical Quality Control Dan Failure Mode Effect And Criticality Analysis Pada PT. Ide Bangun Mandiri
DOI:
https://doi.org/10.21070/ups.5291Keywords:
Quality Control, Statistical Quality Control (SQC), FMECA (Failure Mode Effect and Criticality Analysis)Abstract
Ide Bangun Mandiri has several obstacles production process, this will have a serious impact quality products produced. Based company data, there are 3 divisions production department that often experience defects. First, sewing division was 38.23%, injection was 33.17%, and finishing was 28.59%. This research uses SQC and FMECA methods to make it easier to analyze and identify potential product failures. As well as providing follow-up action on problems that occur. aim of this research is to determine the causes of defects during shoe production SQC method and the analysis stage using FMECA method. The results this research were that the sewing division with RPN value of 240 was production operator who was less careful, injection with RPN value of 252 cause of failure, namely machine maintenance was not done regularly, and finishing with an RPN value of 252 cause of namely the operator was negligent in his work.
Downloads
References
B. J. Hutapea, M. A. Hasmi, dan A. Karim, “Sistem Pendukung Keputusan Penentuan Jenis Kulit Terbaik Untuk Pembuatan Sepatu Dengan Menggunakan Metode VIKOR,” vol. 5, no. 1, hal. 6–12, 2018.
W. H. Afiva, F. Tatas, D. Atmaji, dan D. J. Alhilman, “Penerapan Metode Reliability Centered Maintenance ( RCM ) pada Perencanaan Interval Preventive Maintenance dan Estimasi Biaya Pemeliharaan Menggunakan Analisis FMECA ( Studi Kasus : PT . XYZ ),” vol. XIII, no. 3, hal. 298–310, 2019.
U. Islam, S. Agung, B. D. Bernadhi, dan S. Tools, “PENERAPAN METODE STATISTIQAL QUALITY CONTROL ( SQC ) DAN FAILURE MODE AND EFFECT ANALYSIS ( FMEA ) DALAM PERBAIKAN KUALITAS PRODUK Studi Kasus : PTPN IX KEBUN NGOBO,” hal. 503–515, 2019.
D. Hendrawan, S. M. Wirawati, dan H. Wijaya, “ANALISIS PENGENDALIAN KUALITAS PADA PROSES BONING SAPI WAGYU MENGGUNAKAN STATISTICAL QUALITY CONTROL ( SQC ) DI PT . SANTOSA AGRINDO,” vol. 1, no. 2, hal. 195–206, 2020.
S. Kasus, P. T. Gaya, I. Kharisma, K. Tangerang, dan F. Al Choir, “PELAKSANAAN QUALITY CONTROL PRODUKSI UNTUK MENCAPAI KUALITAS PRODUK YANG MENINGKAT,” vol. 1, no. 4, hal. 1–20.
E. Suprianto, P. S. Teknik, M. Pembekalan, F. Teknik, dan U. N. Bandung, “PENGENDALIAN KUALITAS PRODUKSI MENGGUNAKAN ALAT BANTU STATISTIK ( SEVEN TOOLS ) DALAM UPAYA MENEKAN TINGKAT,” vol. 6, no. 2, hal. 10–18, 2016.
S. Hidayat, R. A. Lubis, dan M. S. A. Majid, “Pengaruh Gaya Kepemimpinan, Kerjasama Tim dan Kompensasi Terhadap Kinerja Karyawan Melalui Kepuasan Kerja Pada PT. Dunia Barusa Banda Aceh,” J. Perspekstif Ekon. Darussalam, vol. 5, no. 1, hal. 86–100, 2019.
J. O. Nasional, “No Title,” vol. 2, no. 1, 2018.
F. Hendra dan R. Effendi, “DAN DAMPAKNYA DENGAN MENGGUNAKAN PENDEKATAN FAILURE MODE EFFECT ANALYSIS ( FMEA ),” vol. 12, no. 1, hal. 17–24, 2018.
A. Bakhtiar, R. D. Pratiwi, dan A. Susanty, “Analisis Kegagalan Proses Produksi Bengkirai Decking dengan Metode FMECA,” hal. 8–9, 2017.
A. Supriadi dan I. Zulkarnaen, “Analisis Pengendalian Mutu pada Proses Produksi Pembuatan Kecap Menggunakan Metode Fault Tree Analysis ( FTA ) dan Metode Failure Mode Efect Analysis ( FMEA ),” vol. 1, no. 1, hal. 31–44.
M. T. Hidayat, P. Studi, T. Industri, F. Teknik, C. Penyok, dan C. Bantat, “GANDENG DENGAN METODE FAULT TREE ANALYSIS ( FTA ) DAN FAILURE MODE AND EFFECT ANALYSIS ( FMEA ) DI PT . XXZ,” vol. 01, no. 04, hal. 70–80, 2020.
U. Ciptomulyono, E. T. Hartanto, F. M. Effect, P. S. Scanner, D. Limiter, dan I. W. Pengantian, “APLIKASI FAILURE MODE EFFECT AND CRITICALITY ANALYSIS ( FMECA ) DALAM PENENTUAN INTERVAL WAKTU PENGGANTIAN KOMPONEN KRITIS RADAR JRC JMA 5310 PADA KRI SATUAN KAPAL PATROLI KOARMATIM,” vol. 6, 2016.
E. Krisnaningsih, P. Gautama, dan M. F. K. Syams, “MENGGUNAKAN METODE FTA DAN FMEA,” vol. 4, no. 1, hal. 41–54, 2021.
V. Kartikasari dan H. Romadhon, “Analisa Pengendalian dan Perbaikan Kualitas Proses Pengalengan Ikan Tuna Menggunakan Metode Failure Mode And Effect Analysis ( FMEA ) dan Fault Tree Analysis ( FTA ) Studi kasus di PT XXX Jawa Timur,” vol. 01, hal. 1–10, 2019.
Downloads
Additional Files
Posted
License
Copyright (c) 2024 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
