Forklift Damage Analysis Using FMEA and FTA Methods At PT. Karya Mitra Tehnik Sidoarjo
Analisa Kerusakan Forklift Menggunakan Metode FMEA dan FTA Pada PT. Karya Mitra Tehnik Sidoarjo
DOI:
https://doi.org/10.21070/ups.2745Keywords:
Forklift, Failure Mode And Effect Analysis (FMEA), Fault Tree Analysis (FTA)Abstract
PT. Karya Mitra Teknik is a company engaged in heavy equipment rental services. Based on the results of observations and interviews, there were several problems in forklift maintenance, which should have been avoided or even did not occur, most of these problems occurred due to undisciplined forklift operators and overuse of forklifts. This study aims to determine the cause of the damage and provide suggestions for improvement. Data processing uses Failure Mode And Effect Analysis (FMEA) and Fault Tree Analysis (FTA). Results of data processing using FMEA will be thoroughly analyzed using the FTA method. The results of the study showed three failure modes that required priority repair, namely, radiator failure mode was damaged with an RPN value of 126, starter dynamo failure mode was damaged with an RPN value of 120 and oil failure mode did not flow to the engine with an RPN value of 105.
Downloads
References
M. R. Apriady, “Implementasi Metode Certainty Factor Dalam Mendeteksi Kerusakan Forklift Merek Linde Active,” J. CyberTech, vol. 3, no. 4, pp. 603–612, 2020.
D. Pordawan, “Analisa Penurunan Kemampuan Sistem Hidrolik Pada Forklift FD 30,” J. Sustain. J. Has. Penelit. dan Ind. Terap., vol. 10, no. 1, pp. 24–31, 2021, doi: 10.31629/sustainable.v10i1.862.
E. Nursanti, R. M. S. Avief, Sibut, and M. Kertaningtyas, MAINTENANCE CAPACITY PLANNING Efisiensi & produktivitas. 2019.
Y. Ngadiyono, “Pemeliharaan Mekanik Industri,” Pendidik. Profesi Guru Jur. Tek. Mesin, pp. 1–112, 2010.
M. Nasution, A. Bakhori, and W. Novarika, “Manfaat Perlunya Manajemen Perawatan Untuk Bengkel Maupun Industri,” Bul. Utama Tek., vol. 16, No. 3, pp. 248–252, 2021.
C. T. N. Siregar, P. Kindangen, and I. D. Palandeng, “Evaluasi Pemeliharaan Mesin dan Peralatan Produksi PT. Multi Nabati Sulawesi (MNS) Kota Bitung,” J. EMBA J. Ris. Ekon. Manajemen, Bisnis dan Akunt., vol. 10, no. 3, p. 428, 2022, doi: 10.35794/emba.v10i3.42362.
M. T. Hidayat, P. Studi, T. Industri, F. Teknik, C. Penyok, and C. Bantat, “GANDENG DENGAN METODE FAULT TREE ANALYSIS ( FTA ) DAN FAILURE MODE AND EFFECT ANALYSIS ( FMEA ) DI PT . XXZ,” vol. 01, no. 04, pp. 70–80, 2020.
A. Andriyanto and Y. Ega Anggraini Putri, “Analisis Penyebab Kegagalan Pengiriman Barang Project 247 Atau Jenis Sxq Pada Divisi Operation Airfreight Pt.Cipta Krida Bahari Dengan Metode Failure Mode and Effect Analysis (Fmea) Dan Fault Tree Analysis (Fta),” J. Logistik Bisnis, vol. 11, no. 1, pp. 7–13, 2021, doi: 10.46369/logistik.v11i1.1372.
R. S. Laali, “ANALISIS KECELAKAAN KERJA PADA BENGKEL BUBUT DAN LAS WIJAYA DENGAN METODE JOB SAFETY ANALYSIS (JSA) DENGAN PENDEKATAN FAILURE MODE AND EFFECT ANALYSIS (FMEA),” Front. Neurosci., vol. 14, no. 1, pp. 1–13, 2021.
Y. Hisprastin and I. Musfiroh, “Pengertian Ishikawa Diagram (Fishbone Diagram),” Maj. Farmasetika, vol. 6, no. 1, pp. 1–6, 2020.
N. Ardiansyah and H. C. Wahyuni, “Analisis Kualitas Produk Dengan Menggunakan Metode FMEA dan Fault Tree Analisys (FTA) Di Exotic UKM Intako,” PROZIMA (Productivity, Optim. Manuf. Syst. Eng., vol. 2, no. 2, pp. 58–63, 2018, doi: 10.21070/prozima.v2i2.2200.
F. Sepriandini and Y. Ngatilah, “Analisis Kualitas Produk Koran Menggunakan Metode Six Sigma Dan Failure Mode and Effect Analysis (Fmea) Di Pt. Xyz Balikpapan,” Tekmapro J. Ind. Eng. Manag., vol. 16, no. 2, pp. 48–59, 2021, doi: 10.33005/tekmapro.v16i2.203.
Y. M. Fitriani, D. Andesta, and H. Hidayat, “Analisis Risiko Kerusakan Pada Mesin Las FCAW Dengan Pendekatan Metode Failure Mode And Effect Analysis (Studi Kasus : PT. Swadaya Graha),” J. Serambi Eng., vol. 7, no. 4, 2022, doi: 10.32672/jse.v7i4.4663.
M. Rinoza, Junaidi, F. Ahmad, and Kurniawan, “Analisa RPN (Risk Priority Number) Terhadap Keandalan Komponen Mesin Kompresordouble Screw Menggunakan Metode FMEA di Pabrik Semen PT. XYZ,” Bul. Utama Tek., vol. 17, no. 1, pp. 34–40, 2021.
S. R. Fauziah, R. Puti, and Selamat, “Identifikasi Penyebab Terjadinya Kecacatan pada Produk Induktor Toroidal dengan Menggunakan Metode Fault Tree Analysis ( FTA ) di,” pp. 91–99.
A. Lestari and N. A. Mahbubah, “Analisis Defect Proses Produksi Songkok Berbasis Metode FMEA Dan FTA di Home - Industri Songkok GSA Lamongan,” J. Serambi Eng., vol. 6, no. 3, 2021, doi: 10.32672/jse.v6i3.3254.
Downloads
Additional Files
Posted
License
Copyright (c) 2023 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
