Optimation of Carburation Heating Method on the Quality of Ubend Cu DHP-R250 Pipe in Coolyng System
Optimasi Metode Pemanasan Karburasi Terhadap Kualitas Bending Ubend Pipa Cu DHP-R250 Pada Sistem Pendingin
DOI:
https://doi.org/10.21070/ups.8548Keywords:
Manufacturing Process, Cooling System, Heating, BendingAbstract
Abstract. manufacturing process in the company in the manufacture of refrigeration unit components, especially in the manufacture of Ubend, this research is intended for the continuity of the manufacturing process in the process of making Ubend in a refrigeration unit due to the obstruction of the bending process in the manufacture of Ubend. The theory used uses literature studies with the taguchi method, while data collection uses documentation and descriptive analysis. The results obtained in this study by using the taguchi method using 4 temperature parameters for heating and 2 experimental parameters for bending, namely bending speed and holding time to reach a radius of 90 °. Then the best temperature in the 200 ° C-600 ° C range is 480 ° C because there are no defects that occur such as ruptures or wrinkles. And the best speed during the bending process is 4.6 seconds / bending.
Downloads
References
S. B. Wicaksono dan M. Basuki, “Analisis Teknis dan Ekonomis Cold Storage Pendingin Ikan Kapasitas 61 Ton Dengan Sistem Refrigerasi Kompresi Uap Vapor Compression Pada KM Natuna,” no. Senastitan Iv, hal. 1–7, 2024.
Guntner, “GUNTNER,” guntner.com. Diakses: 3 Juli 2024. [Daring]. Tersedia pada: https://guntner.com/
B. M. Gaelogoy et al., “ANALISIS SISTEM PENDINGIN DENGAN PENAMBAHAN PIPA KAPILER,”
vol. 6, no. 3, hal. 1–7, 2023, doi: https://doi.org/10.24176/crankshaft.v6i3.11164.
E. Yuliana, “AFoSJ-LAS ( All Fields of Science J-LAS ),” vol. 1, no. 1, hal. 44–53, 2021.
Mochammad Karim Al Amin et al., “Rancang Bangun Alat Pembengkok Pipa (Pipe Bending Tools) Untuk Produk Project Base Learning Meja dan Kursi,” J. Teknol. Marit., vol. 7, no. 1, hal. 1–12, 2024, doi: 10.35991/jtm.v7i1.3.
P. S. Tjahjanti PH, Iswanto, Widodo E, “Examination of Thermoplastic Polymers for Splicing and Bending,” Nano Hybrids Compos. Trans Tech Publ., vol. 38, hal. 87–97, 2023, doi: https://doi.org/10.4028/p-8myjhn.
J. Ariksa, Y. Setiawan, K. Kadriadi, A. Amiruddin, dan A. B. Pratama, “Rancang Bangun Mesin Pemotong Pipa Dengan Las Oxy Acetylene,” Mach. J. Tek. Mesin, vol. 9, no. 1, hal. 13–17, 2023, doi: 10.33019/jm.v9i1.3914.
A. Aisyah et al., “Analisis Pengaruh Biaya Produksi Terhadap Laba Kotor : Literature Review Artikel Terindeks Sinta,” Trending J. Ekon. Akunt. dan Manaj., vol. 2, no. 2, hal. 367–374, 2024.
I. Iswanto, E. Widodo, A. Akbar, dan A. K. Putra, “Perbandingan Induction Hardening dengan Flame Hardening pada Sifat Fisik Baja ST 60,” Mek. Maj. Ilm. Mek., vol. 19, no. 2, hal. 90, 2020, doi: 10.20961/mekanika.v19i2.43203.
C. TANG, “Environmentally friendly antiagglomerants: a promising solution for gas hydrate plugging and corrosion risk management in oil and gas pipelines,” Energy & Fuels, vol. 38.8, hal. 6738–6752, 2024.
A. Gilbran, Y. Oktriadi, dan E. Yudo, “Analisis Pengaruh Parameter Terhadap MRR Pada Benda Kerja di Mesin CNC Turning dengan Metode Taguchi,” J. Inov. Teknol. Terap., vol. 2, no. 1, hal. 9–14, 2024, doi: 10.33504/jitt.v2i1.134.
J. Teknik, M. Universitas, S. Ageng, dan M. Novrindah, “STUDI PERILAKU OKSIDASI SIKLIK PADUAN Ti-6Al-5Nb- 3Zr-1Sn UNTUK APLIKASI MATERIAL BILAH KOMPRESOR BERTEKANAN TINGGI PADA MESIN PESAWAT,” 2024.
T. R. Sanjaya, R. D. Anjani, dan N. Burhan, “Analisis Kekuatan Bending Akibat Variasi Arus Pengelasan SMAW Pada Sambungan Pipa Api 5L GR . B SCH 80,” vol. IX, no. 3, hal. 9848–9856, 2024.
Downloads
Additional Files
Posted
License
Copyright (c) 2025 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
