An Effect of Sansevieria Fiber Length Variation on the Tensile and Compressive Strength in Polymer Matrix Composite Fabrication
Pengaruh Variasi Panjang Serat Sansiviera Terhadap Kekuatan Tarik dan Tekan pada Pembuatan Komposit Matriks Polimer
DOI:
https://doi.org/10.21070/ups.5591Keywords:
Composite, Sansevieria, Tensile Test, Compressive Test, Polyester TesinAbstract
This research explores the effect of variations in Sansevieria fiber length on the tensile and compressive strength of polymer matrix composites. Sansevieria natural reinforcing material because of its high strength and elasticity. Tensile and compressive tests were carried out in accordance with ASTM D-638 and ASTM D-695 standards. Variations in fiber length used are 1 cm, 2 cm, 3 cm, 4 cm and 5 cm. The results show that the specimen with a fiber length of 4 cm has the highest tensile strength of 42.18 MPa, while the specimen with a fiber length of 2 cm has the lowest tensile strength of 33.24 MPa. The highest strain of 11.84% was obtained from 1 cm fibers, while the lowest strain of 9.22% was found in 2 cm and 3 cm fibers. Increasing fiber length generally increases the compressive strength of the composite, with the highest value at 5 cm fibers.
Downloads
References
R. Iskandar Fajri and dan Sugiyanto, “Studi Sifat Mekanik Komposit Serat Sanseviera Cylindrica Dengan Variasi Fraksi Volume Bermatrik Polyster,” Prof.Sumantri Brojonegoro, vol. 1, no. 2, p. 704947, 2013.
B. Sugiantoro, A. Kurniawan, and N. Artati, “Pengaruh Orientasi Cloth dan Roving Serat Sensivera dengan Perlakuan Alkali dan Penguat CNTs Terhadap Kekuatan Bending dan Morfologi (Uji SEM),” vol. 1, no. 1, pp. 1–10, 2022.
B. Maryanti, A. A. Sonief, and S. Wahyudi, “Pengaruh Alkalisasi Komposit Serat Kelapa-Poliester Terhadap Kekuatan Tarik,” Rekayasa Mesin, vol. 2, no. 2, pp. 123–129, 2011.
S. Ali and A. Rusman, “Kuat Tekan Material Dari Bahan Komposit Diperkuat Serat Tandan Kosong Kelapa Sawit (TKKS),” J. Mekanova, vol. 3, no. 5, pp. 128–136, 2017, [Online]. Available: http://180.250.41.45/jmekanova/article/view/861
L. F. Aoladi et al., “Analisis Pengaruh Perlakuan Alkali Terhadap Kekuatan Tarik dan Ketangguhan Impak Komposit dari Serat Lidah Mertua ( Sansevieria Trifasciata ) dengan Matrik Polyester,” Mer-C, vol. 2, no. 2, pp. 22–31, 2019.
D. A. S. Muhamad Muhajir, Muhammad Alfian Mizar and U. N. M. Jurusan Pendidikan Teknik Mesin-FT, “Analisis Kekuatan Tarik Bahan Komposit Matriks Resin Berpenguat Serat Alam Dengan Berbagai Varian Tata Letak,” J. Tek. Mesin, vol. 24, no. 2, pp. 1–8, 2016.
S. A. Rahmawaty, “Analisa Kekuatan Tarik dan Tekuk pada Komposit Fiberglas-Polyester Berpenguat Serat Gelas dengan Variasi Fraksi Volume Serat,” JTM-ITI (Jurnal Tek. Mesin ITI), vol. 5, no. 3, p. 146, 2021, doi: 10.31543/jtm.v5i3.685.
H. N. Beliu, Y. M. Pellle, and J. U. Jarson, “Analisa kekuatan tarik dan bending pada komposit widuri - polyester,” J. Tek. Mesin UNDANA - Lontar, vol. 03, no. 02, pp. 11–20, 2016.
N. Nopriantina and Astuti, “Pengaruh Ketebalan Serat Kepok (Musa paradisiaca) Terhadap Sifat Mekanik Material Komposit Poliester-Serat Alam,” J. Fis. Unand, vol. 2, no. 3, pp. 195–203, 2013.
R. Septyanto, D. Dwilaksana, and Y. Hermawan, “Pengaruh Variasi Panjang Serat Terhadap Kekuatan Tarik Dan Bending Komposit Matriks Polipropilena Dengan Penguat Serat Sabut Kelapa 10%Pada Proses Injection Moulding,” Ilm. Has. Penelit. Mhs., pp. 1–5, 2014.
Downloads
Additional Files
Posted
License
Copyright (c) 2024 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
