Design and Development of an Electrically Powered Oil Suction Device for Two-Wheeled Motor Vehicles
Rancang Bangun Alat Penghisap Oli Pada Kendaraan Bermotor Roda Dua Berbasis Tenaga Listrik
DOI:
https://doi.org/10.21070/ups.10734Keywords:
oil change, preventing engine damage, maintenance assisting toolAbstract
A motorcycle oil suction tool is designed to simplify the oil change process and overcome the limitations of manual methods that are time-consuming and messy. The tool operates using a vacuum system to automatically extract used oil from the engine chamber without opening the drain bolt. The design process includes needs identification, literature study, structural design of the frame and tank, component selection, assembly, and performance testing. Strength analysis using SolidWorks 2024 shows a maximum Von Mises stress of 72.59 MPa, which is below the material yield strength of 172.37 MPa. The maximum displacement (3.4 × 10⁻⁵ mm) and strain (2.52 × 10⁻⁶) are very small and remain within the elastic range. The minimum safety factor of ≥ 2.373 indicates a high level of structural safety. Overall, the device is safe, efficient, cleaner, and faster than conventional manual oil change methods.
Downloads
References
M. Irsyam, “Perancangan Alat Pendeteksi Kelayakan Oli Pada Kendaraan Sepeda Motor Berbasis Arduino Uno Atmega328,” Sigma Tek., vol. 2, no. 2, pp. 179–191, 2019.
A. Agung Wibowo and A. Brahma Nugroho, “Prototype Of Oil Change Notification Tool On Motorcycle Based On Hall Sensor And Esp32 Microcontroller Prototipe Alat Notifikasi Penggantian Oli Pada Sepeda Motor Berbasis Sensor Hall Dan Mikrokontroler Esp32”, doi: 10.24912/tesla.
K. Abimanyu et al., “Perancangan Sistem Monitoring Penggantian Oli Pada Sepeda Motor Berdasarkan Jarak Tempuh,” J. Techno-Socio Ekon., vol. 13, no. 1, 2020.
P. Pujono and R. W. Nur Fauzi, “Rancang Bangun Mesin Flushing Oil,” Bangun Rekaprima, vol. 6, no. 1, p. 15, 2020, doi: 10.32497/bangunrekaprima.v6i1.1926.
A. irma Wantini, G. Sanhaji, R. Mi’raz, and W. L. Buana, “Perancang Dan Implementasi Sepeda Motor Trail Listrik Untuk Pengembangan Produk Di Pt. Len Industri (Persero),” J. Poli-Teknologi, vol. 22, no. 3, pp. 114–125, 2023, doi: 10.32722/pt.v22i3.5775.
A. Nugroho, “Analisis Pengaruh Modifikasi Berat Roller Terhadap Performa Pada Motor Matic 110 Cc Dengan Metode Pengujian Dynotest,” Mach. J. Tek. Mesin, vol. 8, no. 2, pp. 17–21, 2022, doi: 10.33019/jm.v8i2.2926.
O. Muhammad and A. Fahrezi, “Proyek Akhir Rancang Bangun Alat Pemurnian Oli Bekas Mengunakan Metode Filtrasi Dengan Media Pasir Zeolit, Karbon Aktif, Dan Bio Ceramic Ball Program Studi D3 Teknik Mesin Jurusan Teknik Mesin Politeknik Negeri Bali 2024,” 2024.
I. Iswanto, H. Herman, E. Widodo, and A. Fahruddin, “Rancang Bangun Mesin Pencoak Pipa (Pipe Notcher) Multi Dimensi,” J. METTEK, vol. 6, no. 2, p. 111, Jan. 2021, doi: 10.24843/mettek.2020.v06.i02.p05.
A. A. Latif, “Studi Eksperimental Pengaruh Debit Aliran Terhadap Kedalaman Gerusan pada Hilir Pintu Air dengan Dasar Tanah Lempung,” J. Muhammadiyah’s Appl. Technol., vol. 1, no. 2, pp. 132–137, 2023, doi: 10.26618/jumptech.v1i2.8569.
F. Ansori and E. Widodo, “Analysis on Centrifugal Pump Performance in Single, Serial, and Parallel,” JEMMME, vol. 3, no. 2, 2018.
L. Prihasworo, D. Woro Fittrin, U. Yusmaniar Oktiawati, and H. Nur Isnianto dan Yulianus Wahyo Setyono, “Rancang Bangun Smart DC Current and Voltage Monitoring Dengan Thingspeak Pada Simulator PLN Laboratorium Teknik Tenaga Listrik UGM,” 2020.
A. Kurniawan and W. Yandri, “Operasi Motor Listrik Dengan Sistem Kendali Star Delta Menggunakan Plc Zelio Sr3B101Fu,” J. Ensiklopedia, vol. 2, no. 5, pp. 1–6, 2020, [Online]. Available: http://jurnal.ensiklopediaku.org
J. Pendidikan and T. Mesin, “RANCANG BANGUN MESIN POMPA AIR DENGAN SISTEM RECHARGING Oleh,” vol. 2, 2017.
M. N. Politeknik and N. Jakarta, “IMPLEMENTASI PROBLEM BASED LEARNING (PBL) PADA KOMPETENSI TUNE-UP MOTOR BENSIN,” 2019. [Online]. Available: https://www.researchgate.net/publication/334724134
A. I. R. Dengan and P. Hisap, “No Title,” 2025.
E. Saputra et al., “Rancang Bangun Sistem Kontrol Debit Air,” vol. 2, no. 1, pp. 73–80, 2019.
Downloads
Additional Files
Posted
Categories
License
Copyright (c) 2026 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
