Examination of High-Temperature Tests Regarding PolyOxyMethylbenzene(POM) Core Material on Aluminum Composite Panels(ACP)
Investigasi Uji Suhu Tinggi pada Alumunium Composite Panel(ACP) untuk Material Inti PolyOxyMetyhlene(POM)
DOI:
https://doi.org/10.21070/ups.12388Keywords:
Aluminum Composite Panel, Polyoxymethylene (POM), high temperature test, microstructureAbstract
Aluminum Composite Panel (ACP) is widely used in industrial and construction sectors due to its lightweight, corrosion resistance, and structural strength. This study investigates the behavior of Polyoxymethylene (POM) as the ACP core after exposure to 300°C, 350°C, and 400°C for one hour. The ACP consisted of a 5052 aluminum alloy cover, N-193 aluminum adhesive, POM core, and fire-retardant coating. Microstructural observations were conducted before and after testing using an optical microscope (OM) at 1000× magnification. Before testing, the POM contained carbon (C), hydrogen (H), and oxygen (O). After high-temperature exposure, hydrogen and oxygen were released as gases, leaving carbon as the remaining element. Carbon adhered to the aluminum surface and spread over a wider area. The POM remained attached to the aluminum at all tested temperatures, increasing its mass. Carbon did not melt because its melting point is approximately 3,550°C.
Downloads
References
M. Ramesh, M. T. Selvan, and A. Saravanakumar, “Evolution and recent advancements of composite materials in structural applications,” in Applications of composite materials in engineering, Elsevier, 2025, pp. 97–117.
M. S. Ashok Kumar, S. Raghavendra, and K. S. Rudra, Fundamentals of Composite Processing: Materials, Methods and Applications: A Guide to Composite Material Selection. Shashwat Publication, 2024.
E. Lahoz and F. Hernández de Olivares, “Preliminar Assessment of Durability for Aluminium Composite Panels,” in Construction and Building Research, Springer, 2014, pp. 453–461.
P. Mohaney and E. G. Soni, “Aluminium composite panel as a facade material,” Int. J. Eng. Trends Technol, vol. 55, no. 2, pp. 75–80, 2018.
W. D. Callister and D. G. Rethwisch, Materials Science and Engineering: An Introduction. Wiley, 2020. [Online]. Available: https://books.google.co.id/books?id=dmoTEQAAQBAJ
R. Sihotang, B. M. Suherlan, and D. Rahmawaty, “Analisis Perbandingan Penggunaan Gypsum, Grc, Acp, Panel Anyaman Rotan Sintetis Dalam Interior Rumah Dan Gedung,” Jurnal Rekayasa Teknologi Nusa Putra, vol. 7, no. 2, pp. 43–54, 2021.
Rydtooling, “Plastic Melting Temperature Chart：what’s the Melting Point of Different Plastic Materials.” Accessed: May 05, 2025. [Online]. Available: https://www.rydtooling.com/plastic-melting-temperature-chart/
B. K. Goriparthi, P. N. E. Naveen, H. R. Shankar, and S. Ghosh, “Mechanical, wear and fatigue behavior of functionalized CNTs reinforced POM/PTFE composites,” Mater. Res. Express, vol. 6, no. 6, p. 065051, 2019.
Z. Liu, R. Zhang, X. Liu, Z. Yin, Z. Li, and H. Guo, “Optimized preparation and aerospace applications of wear-resistant POM composites: a mini-review,” Journal of Materials Science: Materials in Engineering, 2026.
P. Mallapur, A. S. Reddy, M. A. Umarfarooq, and N. R. Banapurmath, “Polyoxymethylene Reinforced With Multiwalled Carbon Nanotubes and Tungsten Disulfide Hybrid Nanocomposites: Experimental and Micromechanical Studies for Gear Applications,” Polym. Compos., 2026.
R. Prasetia, A. Hariono, A. P. Laksono, and M. F. Agustio, “Performansi keselamatan kebakaran penggunaan aluminum composite panel (ACP) pada bangunan gedung,” Jurnal Permukiman, vol. 18, no. 2, pp. 92–102, 2023.
I. Rustamov, L. Xiang, Y. Xia, and W. Peng, “Filler processing and mixing effects of polyoxymethylene/graphene nanocomposite on tribo-mechanical performances,” Tribol. Int., vol. 201, p. 110267, 2025.
S. Lüftl, V. M. Archodoulaki, and S. Seidler, “Thermal-oxidative induced degradation behaviour of polyoxymethylene (POM) copolymer detected by TGA/MS,” Polym. Degrad. Stab., vol. 91, no. 3, pp. 464–471, Mar. 2006, doi: 10.1016/j.polymdegradstab.2005.01.029.
P. H. T. H. Tjahjanti, A. Fahruddin, M. Mulyadi, S. H. Sujiatanti, M. E. Wicaksono, and R. B. Jakaria, “Core Material Manufacturing Study On Aluminum Composite Panel (ACP),” Jurnal Improsci, vol. 2, no. 3, pp. 186–196, 2024.
M. E. Wicaksono, P. H. Tjahjanti, M. I. Mauliana, and E. Widodo, “Simulasi Numerik Aluminium Composite Panel (Acp) Dengan Variasi Material Inti,” Prosiding Seminar Sosial Politik, Bisnis, Akuntansi dan Teknik, vol. 6, pp. 189–196, Feb. 2025, doi: 10.32897/sobat.2024.6.1.4182.
Mustaka Group, “Apa itu Aluminium Composite Panel?” Accessed: Sep. 04, 2026. [Online]. Available: https://mustakagroup.com/apa-itu-aluminium-composite-panel/
Downloads
Additional Files
Posted
Categories
License
Copyright (c) 2026 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
