DOI of the published article https://doi.org/10.21070/ups.11171
Analysis of the Effect of Hydraulic Pressure Settings on the Pan Handle Installation and Pounding Process on Product Defects
Analisa Pengaruh Pengaturan Tekanan Hidrolik Pada Proses Tumbuk Pemasangan Pegangan Panci Terhadap Cacat Produk Yang Dihasilkan
DOI:
https://doi.org/10.21070/ups.11171Keywords:
hydraulic pressure, Mashing Process, Product Defects, QualityAbstract
This study aims to determine the effect of hydraulic pressure settings in the pan handle installation process on product defect rates. An experimental approach was employed using three hydraulic pressure variations: 245 psi, 275 psi, and 300 psi. Each pressure level was tested on a number of samples, and observations were conducted to identify the types and frequencies of defects that occurred. The collected data were analyzed using Analysis of Variance (ANOVA) to evaluate the effect of hydraulic pressure on product quality. The results indicate that variations in hydraulic pressure have a significant effect on defect rates. Pressure settings of 245 psi and 300 psi resulted in relatively high defect rates of 30% and 48%, respectively, while the 275 psi setting produced the lowest defect rate of only 5%. Therefore, a hydraulic pressure of 275 psi can be considered the optimal condition for improving product quality and minimizing defects.
Downloads
References
N. N. Muryatini et al., “Pengembangan Industri Rumah Tangga Teri Krispi Kusuma,” vol. 7, no. 3, pp. 184–193, 2025.
R. Seri, D. A. N. Paralel, and E. Widodo, “Analisis head pompa sentrifugal pada rangkaian seri dan paralel,” pp. 46–56.
A. Andry, M. Ivanto, and G. S. Lubis, “Rancang Bangun Mesin Press Hidrolik Berkapasitas 5 Ton,” vol. 5, no. 1, pp. 1–6, 2024.
A. Jl, C. Raya, K. Serang, and K. Serang, “Implementasi Sistem Hidrolik Pada Mesin Spandek Produksi di PT Primaland Juniwan,” vol. 2, no. 3, 2024.
D. Uji and T. Kerja, “Pada silinder hidrolik,” vol. 10, pp. 59–66, 2024.
R. D. Jayanto, E. Widodo, R. Firdaus, and A. Akbar, “The Manufacturing Planning of Installation Series-Parallel Combination Centrifugal Pump Testing Equipment Perencanaan Manufaktur Instalasi Pompa Sentrifugal Laboratorium Teknik Mesin Dengan Kombinasi Rangkaian Seri dan Paralel,” vol. 6, no. 1, 2021.
J. T. Mesin, F. Teknik, and U. M. Buana, “Analisis Kebocoran Sistem Hidrolik Pada Landing Gear,” vol. 1, no. 2, pp. 65–74, 2021.
M. I. Pasaribu et al., “ANALISIS PERAWATAN ( MAINTENANCE ) MESIN SCREW PRESS DI PABRIK KELAPA SAWIT DENGAN METODE FAILURE MODE AND,” vol. 9, no. 2, pp. 104–110, 2021.
A. Perawatan et al., “Jurnal SENOPATI,” pp. 32–45, 2022.
M. S. Ishlah, P. Vitasari, and E. Adriantantri, “ANALISIS PENYEBAB TERJADINYA CACAT PRODUK MENGGUNAKAN STATISTICAL PROCESS CONTROL PADA PROSES PRODUKSI PLYWOOD,” vol. 8, no. 2, pp. 146–151, 2025.
A. P. T. Abc, “SIGMA DAN FMEA UNTUK MENGURANGI PRODUK CACAT PANCI,” pp. 294–304.
A. Prasetyo, S. Mulyono, A. Milah Muhammad, and M. Muslimin, “Modifikasi Sistem Clamping dan Injection pada Prototipe Injection molding Double Barrel dengan Sistem Hidrolik,” J. Mek. Terap., vol. 5, no. 3, pp. 133–142, 2025, doi: 10.32722/jmt.v5i3.7079.
T. S. Gumilang, R. Krisnaputra, S. Sugiyanto, I. A. Hendaryanto, I. S. Irawati, and G. Bahari, “Perancangan Sistem Hidrolik Pada Mesin Press Bambu Laminasi,” J. Rekayasa Mesin, vol. 14, no. 3, pp. 963–978, 2023, doi: 10.21776/jrm.v14i3.1484.
T. Pratomo, R. D. Yani, M. Effendi, and D. Iswanda, “Prototipe double acting cylinder transparan sebagai media pembelajaran sistem hidrolik,” vol. 10, no. 1, pp. 84–92, 2021.
J. Multidisiplin and S. Volume, “No Title,” vol. 2, no. 12, pp. 86–96, 2024.
S. Hidrolik, R. Marking, and E. Machine, “MESIN PENGHAPUS MARKA JALAN,” vol. 5, no. 2, pp. 122–131, 2020.
M. Naufal, H. Musyaffa, N. Sinaga, and B. Yunianto, “NUMERIK,” vol. 11, no. 3, pp. 338–343, 2023.
J. Ferdani, I. M. Sunada, and M. Ali, “ANALISA PERFORMA HIDROLIK MEJA MAINTENANCE LARAS MERIAM 57mm S-60 ANTI AIRCRAFT,” Transmisi, vol. 16, no. 1, 2020, doi: 10.26905/jtmt.v16i1.4495.
Komarudin, Y. I. Pratama, and I. Soleh, “Perancangan Power Unit Sistem Hidrolik untuk Payung Hidrolik di Masjid Raya Aceh,” J. Tera, vol. 2, no. 1, pp. 34–47, 2022, [Online]. Available: https://jurnal.undira.ac.id/jurnaltera/article/view/159
A. W. Lestari, Z. Marlita, V. Sefiya, I. A. Prasetyo, and U. N. Semarang, “Analisis Varian ( Anova ) : Konsep , Langkah-Langkah Dan Penerapanya Dalam Analisis Data Analysis of Variance ( ANOVA ): Concept , Steps , and Its Application in Data,” vol. 6, no. 1, pp. 178–182, 2025.
M. `Choirul U. Nuha and Samsudi, “Pengaruh variasi kuat arus dan tekanan gas pelindung terhadap kekuatan tarik hasil pengelasan MIG (metal inert gas) pembuatan front chasis mobil listrik dengan bahan ST 60,” J. Mech. Eng. Learn., vol. 11, no. 2, pp. 1–11, 2022.
G. Agustiono, T. Industri, F. Teknik, U. Maarif, and H. Latif, “Prosiding SemNas Teknik UMAHA Fakultas Teknik UMAHA ISSN 2721-2662 (online),” vol. 2662, pp. 98–106.
C. Meisita and C. Sheets, “ANALISIS PENGENDALIAN KUALITAS UNTUK MEMINIMUMKAN,” vol. 13, no. 5, pp. 709–718, 2024.
D. A. N. Fmea, U. Menurunkan, D. Pada, and P. Assembly, “Analisa penyebab cacat produk menggunakan metode rca dan fmea untuk menurunkan defect pada proses assembly,” vol. 4, no. 2, pp. 67–74, 2026.
Downloads
Additional Files
Posted
Categories
License
Copyright (c) 2026 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
