Design of a Tuber Chips Cutting Machine with a Single-Phase Electric Motor Drive 0,33 HP (0.24681 kW)
Perancangan Desain Mesin Pemotong Keripik Ubi Dengan Penggerak Motor Listrik Single Phase 0,33 HP (0,24681 kW)
DOI:
https://doi.org/10.21070/ups.10501Keywords:
Chip Cutting Machine, Machine Design, Safety FactorAbstract
This study aims to design and improve a 0.33 HP single-phase electric motor-driven cassava chip cutting machine, focusing on four aspects: machine design, shaft component mechanical calculations, frame force simulation, and blade tilt modification. The blade tilt modification enhances the slicing effect, reducing broken slices. Mechanical calculations determine the shaft's strength under rotational loads, while frame force simulation evaluates the safety factor, ensuring the frame can withstand dynamic and static loads without deformation. The results show an efficient and safe design, prioritizing operator safety and hygiene, though not including all necessary manufacturing drawings. Simulation results indicate a maximum deformation of 8.5901e-6 m, equivalent stress of 56 MPa, equivalent elastic strain of 9.9168e-6 m/m, a maximum safety factor of 15, and a minimum shaft diameter of 22.5 mm.
Downloads
References
“View of Rancang Bangun Mesin Penggerak Untuk Alat Pembuat Keripik Pisang Otomatis _ Prosiding SEMNAS INOTEK (Seminar Nasional Inovasi Teknologi).pdf.”
A. C. Surbakti, “Rancang Bangun Mesin Pengiris Ubi Dengan Kapasitas 30 Kg/jam,” Invotek Polbeng, vol. 07, no. 1, pp. 1–5, 2009.
Wijoyo, Savitri, B. Mukti, and Y. Y. Kristiawan, “Rancang Bangun Mesin Pemotong Model Spiral Untuk Meningkatkan Produksi Keripik Di Ukm Sulis,” Abdi Masya, vol. 3, no. 2, pp. 81–87, 2022, doi: 10.52561/abma.v3i2.336.
K. Produksi, D. A. N. Mutu, and K. Di, “Introduksi Teknologi Mekanis Untuk Meningkatkan Efisiensi, Kapasitas Produksi Dan Mutu Keripik Di Ukm Kabupaten Blitar,” Teknol PANGAN Media Inf dan Komun Ilm Teknol Pertan, vol. 9, no. 1, pp. 87–95, 2018, doi: 10.35891/tp.v9i1.913.
J. Akuntansi, M. D. A. N. Ekonomi, M. Zai, D. S. Chaerani, and H. Gusvita, “Analisis Usaha Pengolahan Ubi Kayu Menjadi Aneka Keripik Singkong Pada Usaha UMKM Bintang Jaya 4x7 Kota Padang,” vol. 3, no. 1, pp. 31–45, 2024.
A. M. Idkhan, “Analisis Penerapan Mesin Pengiris Umbi untuk Olahan Keripik di Makassar,” J Tek Teknol, vol. 16, no. 1, pp. 12–17, 2017.
Suherman, Muharnif, S. A. Syahputra, and M. Harahap, “Review Mesin Pengiris Keripik Singkong,” ATDS SAINTECH -Journal Eng, vol. 2, no. 2, pp. 29–37, 2021, [Online]. Available: https://ojs.atds.ac.id/index.php/atdssaintech/article/view/34/32
D. T. Mesin, F. Teknik, U. N. Surabaya, J. Teknikmesin, and F. Teknik, “MESIN PENGUPAS DAN PEMOTONG KENTANG SEMI OTOMATIS Ageng Aldrianto Arya Mahendra Sakti Abstrak,” pp. 69–75.
D. Sudut, D. A. N. Terhadap, K. Daya, H. Pemotongan, and D. A. N. Quantity, “Jurnal teknik mesin,” vol. 3, no. 1, pp. 54–59, 2022.
M. A. Fahmi, D. Riandadari, and F. I. Abdi, “Analisis Kecepatan Putaran dan Jumlah Mata Pisau Stainless Steel terhadap Hasil Produksi pada Mesin Cutting Ubi Jalar,” vol. 08, no. 02, pp. 141–149, 2023.
“Analisis+Distribusi+Tegangan+pada+Rangka+Utama+Mesin+Uji+Tarik+Kapasitas+2500kg+Menggunakan+Ansys+Workbench+R1+2023.”
T. Mulyanto and A. D. Sapto, “Analisis Tegangan Von Mises Poros Mesin Pemotong Umbi-Umbian Dengan Software Solidworks,” Presisi, vol. 18, no. 2, pp. 24–29, 2017.
E. Prasetia, I. M. Widiyarta, I. Wayan, and A. Darma, “Simulasi Analisa Struktur Steering Knuckle Mobil Hemat Energi Naga Pasa Evo I Weimana Menggunakan Ansys Workbench,” vol. 14, no. 3, pp. 235–239, 2025.
T. Davareza, A. Nataria, F. Ganda, D. Wulandari, D. D. Mubarok, and G. P. Firmansyah, “Studi Finite Element Analysis terhadap Kekuatan Struktural Dua Desain Roda Kereta Menggunakan ANSYS,” vol. 10, no. 03, pp. 628–637, 2025.
A. B. Prasetiyo et al., “Finite Element Analysis ( FEA ) of blade weed design using Ansys workbench,” vol. 26, no. 3, pp. 371–378, 2022.
I. Dumyati and S. Nurhaji, “Modeling dan Simulasi Finite Element Analysis pada Segitiga T Sepeda Motor Menggunakan Sofware Ansys 2023,” vol. 5, no. 1, 2023.
T. Tasliman, A. M. Alam, A. Santoso, Y. Dwi, B. Habib, and D. W. Soedibyo, “Design and Technical Evaluation of a Tempeh Slicer Using Stainless Steel Rotating Disc with Three Curved Blades,” vol. 14, no. 3, pp. 920–932, 2025.
Downloads
Additional Files
Posted
Categories
License
Copyright (c) 2026 UMSIDA Preprints Server
This work is licensed under a Creative Commons Attribution 4.0 International License.
